>>Concrete
  • egg-beater-pail-mixer
    The eggbeater or mud mixer is a simple stirring rod that allows for the full dispersion of the polymer throughout the coated aggregate mix. Used with a 1/2 HP low RPM drill for the best results.
  • flexset-concrete-repair-3gal
    Originally developed as a rapid runway concrete repair system for the military, FlexSet has become a cost-effective alternative to traditional spall repair, driveway concrete repair, floor repair and other concrete restoration procedures. The Roklin difference with Flexset Concrete Repair is that it utilizes a naturally rounded sand, which is polymer coated in our plant. This type of aggregate greatly enhances flow ability and increases the overall strength of the crack repair. Listed below are some of the advantages that FlexSet Concrete Repair Product offers vs. conventional materials:
    • Minimal preparation required
    • No costly demolition necessary
    • Set-up in less than 10 minutes
    • Odorless & vapor-less
    • Exceptional bond to concrete
    • Unaffected by extreme heat or cold
    • Seals & waterproofs
    • Good chemical resistance to oils, fuels, and antifreeze
    • Outstanding durability
    • High-traction surface
  • polyflex-ds-3gal
    PolyFlex DS is designed for the experienced users of Roklin’s products. PolyFlex DS was formerly known as Dopey Soup and can be used for concrete repair or asphalt repair. Available for use with almost any type of aggregate that is available locally, PolyFlex DS must be used with aggregate that is very clean, free of dust & debris, and dry. We recommend the use of our specially-coated sand for the best possible results. PolyFlex DS chemicals and aggregates must be carefully measured to achieve the correct ratio. It is also important that you do adequate testing for your specific application. Performance may vary depending on the type of aggregate used and the type of end use. This product is not recommended for first-time users of Roklin’s concrete and asphalt repair products.
  • polyflex-ds-3gal
    PolyFlex DS is designed for the experienced users of Roklin’s products. PolyFlex DS was formerly known as Dopey Soup and can be used for concrete repair or asphalt repair. Available for use with almost any type of aggregate that is available locally, PolyFlex DS must be used with aggregate that is very clean, free of dust & debris, and dry. We recommend the use of our specially-coated sand for the best possible results. PolyFlex DS chemicals and aggregates must be carefully measured to achieve the correct ratio. It is also important that you do adequate testing for your specific application. Performance may vary depending on the type of aggregate used and the type of end use. This product is not recommended for first-time users of Roklin’s concrete and asphalt repair products.
  • Sale! polyflex-ds-10-minute-repair
    PolyFlexDS repairs set up to a more flexible repair. PFDS is ideal where there is a lot of motion in the pavement. The polymer is a natural color and can be topped with gray or black sand to match your pavement. Make sure the crack is clean and free of moisture. If there is a lot of water, use a blow dryer or torch to make certain the crack is dry. Open cartridge and squeeze PFDS directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time.
  • Sale! Concrete Welder Gray
    Sealing concrete cracks is simple with Concrete Welder in cartridges. Make sure the crack is clean and free of moisture. If there is a lot of water, use a heat lance or torch to make certain the crack is dry. Open cartridge and squeeze Concrete Welder directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time. Color: Grey
  • polyflex-ds-10-minute-repair
    Sealing concrete cracks is simple with Concrete Welder in cartridges. Make sure the crack is clean and free of moisture. If there is a lot of water, use a heat lance or torch to make certain the crack is dry. Open cartridge and squeeze Concrete Welder directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time. Color: Grey
  • flexset-concrete-repair-5gal
    Originally developed as a rapid runway concrete repair system for the military, FlexSet has become a cost-effective alternative to traditional spall repair, driveway concrete repair, floor repair and other concrete restoration procedures. The Roklin difference with Flexset Concrete Repair is that it utilizes a naturally rounded sand, which is polymer coated in our plant. This type of aggregate greatly enhances flow ability and increases the overall strength of the crack repair. Listed below are some of the advantages that FlexSet Concrete Repair Product offers vs. conventional materials:
    • Minimal preparation required
    • No costly demolition necessary
    • Set-up in less than 10 minutes
    • Odorless & vapor-less
    • Exceptional bond to concrete
    • Unaffected by extreme heat or cold
    • Seals & waterproofs
    • Good chemical resistance to oils, fuels, and antifreeze
    • Outstanding durability
    • High-traction surface
  • variflo-upright-polymer-dispenser

    Variflo Upright Polymer Dispenser

    Call For Price - 1.877.353.9738
    VariFlo is a lightweight portable machine that can be transported in the back of a pickup truck. The machine has a bracket that allows the machine to be hung quickly and easily wherever it is most convenient to the user: on a tote, drum, fence, or tailgate. Some government agencies have even customized their vehicles for the VariFlo machine so that they are always ready for fast repairs. VariFlo can also be attached to a lightweight dolly and rolled along the repair project. For highway repairs or extensive damage, use the highly portable VariFlo Upright Polymer Dispensing machine which can be set up and used by one person in just a few minutes. The VariFlo machine dispenses Concrete Welder (available in gray, dark gray, and black) to quickly and easily repair large volume pavement damage.

    Benefits of Polymer Repair Using VariFlo Upright Polymer Dispensing Machine:

    • Two component polyurethane systems designed to support heavy traffic loads.
    • Chemical resistance to oils, hydraulic fluids, diesel, and gasoline.
    • Flexible enough to minimize bond stresses and thermal stresses.
    • Low viscosity ensures deep penetration to county hydraulic pumping action.
    • Rapidly setting for quick return to traffic.
    • Fills voids to extend life expectancy of concrete.
    • Restore aggregate interlock for better load transfer and slab stabilization.
    • Minimal prep and no demolition or removal significantly reduces labor requirements.
    • Reduced repair times allow for faster return to traffic with minimal interruption and safer work environment.
    • No training required
    • Repair time is counted in minutes - not hours
    • Last longer than conventional repair materials.
    • Can be applied over a wide temperature range.
    • Safe to use, no VOC’s and closed delivery system eliminates exposure concerns.
    • Grade restoration enhances smooth ride.
    • Cost effective
  • concrete-welder-50gal
    Concrete Welder is a low viscosity, fast-reacting urethane polymer, which is applied with Roklin's Vari-Flow dispensing equipment, specially designed for this product. It is recommended for larger highway and other projects where extensive repairs are needed. It can be used with a variety of aggregate materials, depending on the requirements of the specific application. Multiple repairs can be completed in rapid succession with minimal traffic closure time. Concrete Welder is a multi-purpose material that works well for both concrete and asphalt repairs. It allows the user to solve several problems with one material. Because it is a very thin liquid it can penetrate into small cracks and forms a high strength adhesive bond between broken structures. Concrete Welder will flow underneath cracked or spalled concrete and seal the base against further erosion from water. The product acts to waterproof and seal concrete and asphalt from the top to prevent water or other liquids from streaming under the slab and creating voids. Concrete Welder has excellent chemical resistance to oils, hydraulic fluids, gasoline, and salts, and antifreeze. Concrete Welder is also safe to use. It contains no solvents, has no odor, and has low toxicity.
  • polyflex-ds-10-minute-repair
    PolyFlexDS repairs set up to a more flexible repair. PFDS is ideal where there is a lot of motion in the pavement. The polymer is a natural color and can be topped with gray or black sand to match your pavement. Make sure the crack is clean and free of moisture. If there is a lot of water, use a blow dryer or torch to make certain the crack is dry. Open cartridge and squeeze PFDS directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time.
  • concrete-welder-50gal
    Concrete Welder is a low viscosity, fast-reacting urethane polymer, which is applied with Roklin's Vari-Flow dispensing equipment, specially designed for this product. It is recommended for larger highway and other projects where extensive repairs are needed. It can be used with a variety of aggregate materials, depending on the requirements of the specific application. Multiple repairs can be completed in rapid succession with minimal traffic closure time. Concrete Welder is a multi-purpose material that works well for both concrete and asphalt repairs. It allows the user to solve several problems with one material. Because it is a very thin liquid it can penetrate into small cracks and forms a high strength adhesive bond between broken structures. Concrete Welder will flow underneath cracked or spalled concrete and seal the base against further erosion from water. The product acts to waterproof and seal concrete and asphalt from the top to prevent water or other liquids from streaming under the slab and creating voids. Concrete Welder has excellent chemical resistance to oils, hydraulic fluids, gasoline, and salts, and antifreeze. Concrete Welder is also safe to use. It contains no solvents, has no odor, and has low toxicity.
  • concrete-welder-50gal
    Concrete Welder is a low viscosity, fast-reacting urethane polymer, which is applied with Roklin's Vari-Flow dispensing equipment, specially designed for this product. It is recommended for larger highway and other projects where extensive repairs are needed. It can be used with a variety of aggregate materials, depending on the requirements of the specific application. Multiple repairs can be completed in rapid succession with minimal traffic closure time. Concrete Welder is a multi-purpose material that works well for both concrete and asphalt repairs. It allows the user to solve several problems with one material. Because it is a very thin liquid it can penetrate into small cracks and forms a high strength adhesive bond between broken structures. Concrete Welder will flow underneath cracked or spalled concrete and seal the base against further erosion from water. The product acts to waterproof and seal concrete and asphalt from the top to prevent water or other liquids from streaming under the slab and creating voids. Concrete Welder has excellent chemical resistance to oils, hydraulic fluids, gasoline, and salts, and antifreeze. Concrete Welder is also safe to use. It contains no solvents, has no odor, and has low toxicity.
  • concrete-welder-50gal
    Concrete Welder is a low viscosity, fast-reacting urethane polymer, which is applied with Roklin's Vari-Flow dispensing equipment, specially designed for this product. It is recommended for larger highway and other projects where extensive repairs are needed. It can be used with a variety of aggregate materials, depending on the requirements of the specific application. Multiple repairs can be completed in rapid succession with minimal traffic closure time. Concrete Welder is a multi-purpose material that works well for both concrete and asphalt repairs. It allows the user to solve several problems with one material. Because it is a very thin liquid it can penetrate into small cracks and forms a high strength adhesive bond between broken structures. Concrete Welder will flow underneath cracked or spalled concrete and seal the base against further erosion from water. The product acts to waterproof and seal concrete and asphalt from the top to prevent water or other liquids from streaming under the slab and creating voids. Concrete Welder has excellent chemical resistance to oils, hydraulic fluids, gasoline, and salts, and antifreeze. Concrete Welder is also safe to use. It contains no solvents, has no odor, and has low toxicity.
  • polyflex-ds-10-minute-repair
    Sealing concrete cracks is simple with Concrete Welder in cartridges. Make sure the crack is clean and free of moisture. If there is a lot of water, use a heat lance or torch to make certain the crack is dry. Open cartridge and squeeze Concrete Welder directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time. Color: Grey
  • polyflex-ds-10-minute-repair
    PolyFlexDS repairs set up to a more flexible repair. PFDS is ideal where there is a lot of motion in the pavement. The polymer is a natural color and can be topped with gray or black sand to match your pavement. Make sure the crack is clean and free of moisture. If there is a lot of water, use a blow dryer or torch to make certain the crack is dry. Open cartridge and squeeze PFDS directly into the crack. Use a scraper or straight-edge to smooth the material out. Wipe up any excess material and allow to dry for 30 minutes. Now the crack is filled and ready for use. Roklin’s long-lasting solution is complete with almost no preparation and little drying time.